How to Get a New Key for Subaru

You can lock and unlock your Subaru with the touch of one button if you have keys. If the key fob was lost in the sea, or washed in the washing machine or washed in the washing machine, it might not work.

Our Stocker Subaru dealership can help. The first step is to access your key fob and locate the circuit board that controls the transmitter within.

How to Get a New Key

Getting a new key for a Subaru is much simpler than you might think. It's possible to get an additional key at the dealer, an auto locksmith or even online. The cost will vary based on the place you purchase the key and if it is required to be programmed. It also depends on the kind of key (transponder or smart fob? Push to start? Regular non-transponder?)

It's best to contact an auto locksmith who has expertise in Subaru automobiles if you're in need of a new car key. They'll be familiar with the unique key fobs as well as the specific key programming that comes with them. If you're unsure which type of key you have, look at the sticker on your windshield to find out.

Certain keys come with Remote Start features which allow you to start your car from the comfort of your home. You'll also require the VIN number of the car which is located on the label in the door to the driver's side or in the owner's manual.

The majority of Subaru models made after 2000 come with a transponder key that deactivates the engine computer. Keys cannot be duplicated using the same equipment that cut metal keys. You'll have to visit a dealership or locksmith to obtain replacement keys. A new key costs between $50 and $250, depending on the model.

how to get a spare subaru key do I obtain a replacement key

There are a variety of ways to obtain an additional key for your subaru outback key, depending on the type of car you have (chip smart fob, intelligent fob "push to start" remote, or a regular key made of metal). Contact the dealership that you bought the car from to request a Replacement key For Subaru forester key, an locksmith in the automotive field who has required equipment to make keys for these types or purchase one online. You can obtain a replacement key from your dealership. It will be guaranteed to fit the vehicle you purchased it, will be covered by warranty, and will be programmed for your model.

For a chip key, the dealership will need to have the codes for the specific vehicle you own, which can only be done at the dealership where you bought the car. This could be an inconvenience because you'll need to either take your car there or get an automotive locksmith to come out and code the key on site.

A standard metal key does not require being coded and can be duplicated by a majority of locksmiths or hardware stores who offer a variety of blank keys. You'll need a key made of metal or flathead screwdriver in order to open the small tabs on the top of the key fob and remove the battery. Replace the battery with a CR2032 coin cell and snap the encasement in place.

How do I obtain an electronic key fob

A key fob is a remote device that allows you to control the electrical systems. They can unlock and start your car or lock it, set the alarm, and many more. If your Subaru key fob isn't functioning correctly, you may have to replace it. However, it is important to make sure that you're getting the right kind of fob for your car. Consumer Reports says that off-brand fobs may cause problems with the immobilizer feature of your car.

If you own a brand newer Subaru is likely that it has an intelligent key system. They require a special programming process to be compatible with your vehicle. This is best handled by your dealer, and the cost can be covered by your warranty or roadside assistance program.

Older Subaru models utilize keys made of steel which can be duplicated at a hardware store or locksmith. You can also buy blank keys from online stores that sell Subaru logo keys.

You can repair the problem with the battery on your older Subaru at home, without having to visit an expert mechanic or pay for a key duplication service. Find a small crevice in the seam that separates the front and back of the fob. Make use of a flathead screwdriver to pull the two halves apart. There's a flat battery inside. Remove the old battery and replace it with a new 2025-type battery in and make sure the correct side is facing up. Place the metal key into the slot and snap everything together.

How to replace a Key Fob

In the past, it was common for people to buy a key fob for a low price at a hardware store or online and then take it to a locksmith or dealer to have it cut and programmed. While this is still a possibility but it's best to directly contact the dealer to avoid the possibility of the key being copied and to ensure that your new key fob is programmed for your vehicle. This is important in the event that your vehicle is a newer model that requires specialized programming, for example, ones with features like automatic parking and window rolling.

These fobs are handy for driving your Subaru in Gilroy but can be an issue when the buttons stop working. You can replace your key fob's battery on your own, in case you're familiar with the process.

Begin by locating the small space in the seam which separates the front from the back of your fob. Utilize a flathead or the tip of a screwdriver made of steel to remove the fob and look inside for the flat round battery. Take the old battery out and then insert a brand new 2032 battery in its place, making sure it's facing the same way that the original one. Then, put the fob back together.

In the near future the keys to your car will be replaced with "smart" keys with more functionality. You can still use the features of your subaru car key replacement key fob until then. It will automatically open your window when your engine is running.